Paint line, screen printing lines 
 First partition and ceiling of the spray booth: 

 1 compartment: 

 → workshop Specifications: L12500mm the * W6800mm * H2800; --------- clean compartment 

 → Jiangsu, South China, the production of polystyrene sandwich color plate (δ = 50mm) wall thickness of δ = 0.472; 

 → design height of 2800mm; 

 → corner and floor cable and cross-point arc chamfering processing, using a dedicated connection aluminum; 

 → single door specifications: W800 * H1900mm; fan 

 → double doors Specifications: W1200 * H1900mm; 1 fan 

 → Perspective window Specifications: W1800 * H1200mm; fan 

 2, clean lighting: 

 → double-barreled 40 * 2W ceiling purification of fluorescent lamps; 

 A total of 16; 

 → Power switches, sockets, specify the installation site customer requirements; 

 → wire RZ-BV-500V-2.5mm2; 



 Second roll coating, self-leveling floor paint and outside the workshop floor paint: 

 1, self-leveling floor paint: 

 → hormone treatment: First batch knife to remove the cement surface of the particles and debris, cleaned with a broom, and then grinding machine fully polished cement surface is clean, rough, and then cleaned. With a vacuum cleaner to suck dust. (With the oil spill should be with a cleaning agent to wash, wet at the required drying cracks at the required resin putty catch level); 

 → Primer: resin and hardener mixed in proportion to Stir, coating evenly with a trowel, so that the cement surface to form a full resin surface; 

 → Tu in: until the bottom is fully cured, the resin and curing agent mixed in proportion, and adding an appropriate amount of filler, stir well, coating evenly with a trowel, so that it can fill the cement surface of the pinhole. 

 → top coating: the coating is fully cured, fully polished using polishing the surface of particles, cleaned, and the vacuum cleaner exhaust dust, fabric filters filter in proportion to add hardener, stir well, coating evenly with a trowel to be cured, so that the entire floor flat, sturdy, so as to achieve compression, shock, dust better. 

 → Construction areas: self-leveling spray and the last parts workshop ---- 12.5 * 6.8 * 1.05 = 90 square meters; 

 2, roller, floor paint: 

 → Construction range: external parts shop ---- 320 +96-90 = 326 square meters; 



 Third. Airshower: 

 A single dual-hair shower room: ----- 1 

 → access to clean workshop will air shower room, single hair shower room; 

 The → Airshower Dimension Specification: L1000 * W1600 * H2100 mm; 

 The → Airshower effective sizes: L1000 * The W800 * H1900 mm; 

 → outer seal plate t = 1.5mm cold plate production within the seal plate with 1.2mm stainless steel mirror bending production, internal duct 1.2 cold plate bending production; 

 → return air distribution on both sides of the position, plus the early effect of the filter, side return air, outside the closure plate 5mm aperture perforated plates; 

 → using the 1HP snail Fan Yun-Feng, the number of nozzle is 12, the wind speed is 18-20m / s, the wind leaching cycle for 0-99s adjustable photoelectric control switch; 

 → doors with single door and two door closers, door additional perspective window with ring lock, double door interlock air shower, usually two-door electronic interlocking; 

 → electronic control system set, install the door frame side; 



 Fifth power of fresh air cabinet: ----- 1 

 (1) for the air handling unit 

 → blower using the outdoor into the installation location to be the scene rational design; 

 → enclosure with high-quality steel plate ∮ ≥ 0.5mm and coated sandwich of polystyrene, ∮ = 50mm color steel plate; 

 → fan lying pump for wind fan, preliminary design, horsepower is 30HP power; 

 → shutters (waterproof, large-scale waste and other debris, the role of) a filter plate non-woven filter 600 * 600, the installation method uses the L30 angle iron frame, locking pressure on the bracket using a dedicated withhold; 

 → two filter bag non-woven filter 600 * 600 Installation Methods L30 angle iron frame, using the special withholding locking pressure on the bracket, and a filter between the width is 600mm; 

 → other accessories to produce: the fan bottom with a damping system, air duct and fan connection using a soft cloth connector to the damping effect; 

 → a filter cotton open the door for the cleaning of cotton filters to replace as well as throughout the cycle; 

 → fan room to open two doors for the two bag filter cotton replacement, as well as the entire cycle of cleaning; 

 → according to the conventional production methods; 

 2 for wind patio 

 → The fresh air design uses FFU for wind courtyard of fresh air into the spray cabinet, and the branch part of the workshop staff to external isolation; 

 → for wind patio size range: L1800 * W1200mm; 

 → patio mounting body color steel plate production, internal party system frame; 

 → is installed inside the sub-high efficiency filter selection jp-GKS-type resistance to humid sub-efficiency air filters, the specifications for the L595 * W595 * H150 efficiency of 99.99%; 

 → air inlet duct louver type outlet into the the FFU style for wind patio; 

 → PVC hanging curtain for special intermediate purification zone and more advanced to purification regional airflow dust separated by the special auxiliary, stainless steel board withhold FFU frame the edge; 

 → by FFU filter to send under the air can effectively achieve the purification, the purification level of 100 000; 

 3, for air ducts and air vents ------- 1 sets air supply pipe 

 → The fresh air with 0.7mm galvanized sheet folded system of pipes, the main channel specification 500 * 800, duct 500 * 600,500 * 500; 

 → main duct length of 40 m / ------ 1 40 m 

 Branch duct length of 20 m / ------ 1 set of 20 m 



 Fifth, the waste gas treatment cabinet -------------- according to customer requirements to consider the need for 



 Sixth, the spray drying production conveyor line: ----- 1 

 A tunnel-type drying furnace 

 A transmission line of the body: ----- 1 

 → line body specifications: L29500 * W1150 * H750mm; 

 → use Specifications: L29500 * W1000mm; 

 → 1-inch ball chain with a # 10 stainless steel light circle drive transport at intervals of about 152.4mm a chain branching,, capped with 15 * 10 * 1.5 (mm) stainless steel mesh belt; 

 → power configuration used: A: Taiwan brand "Taiwan state the 3HP gear reducer motor drive, the speed ratio 60:1; 

 C: 3HP Taiwan brand "Scholastic" converter, the speed range of 0.4 ~ 4m/min; 

 → rail bracket 50 * 50 iron side-pass welding production; 

 → foot cup of the M16 * 80 can be adjusted; 

 → overall paint treatment; 

 2, the drying furnace: 

 → Dimension: L16000mm * W1150mm * H500mm; 

 → internal specifications: L16000mm * W1000mm * H300mm; 

 → outer plate with 50mm rock wool board production, import and export lid δ1.2mm galvanized sheet produced two height adjustment plate; 

 → Automatic thermostat controlled, room temperature -120 degree of controllability; 

 → heat source using a stainless steel heat pipe heating, power 72KW; 

 → control system with electronic control box and electrical components of domestic electrical components production; 

 → lid at the top to install the two emission port, using the adjustable; 

 → overall paint treatment; 

 3, cooling parts: 

 → Size: L2000mm × W1150mm × H650mm. 

 → body, tripod with δ1.5mm monolithic folded, adjustable foot pi. 

 → frame 1.5mm cold plate folded into the outer layer of barbed wire sealed cover, the average installed at the top of the 8-inch Axial bucket fan. 

 → cooling side with a small fan for cooling. 



 Two. Single injection counters ------- 4 

 → cabinet Specifications: W1800 * D2200 * H2100mm, tank high 450mm; 

 → work space efficient: W1700 * D1350 * H1300mm; 

 → injection counters assembled structure, using the screw connection; 

 → injector cabinet base cabinet with fold system of δ1.5mm galvanized plate welded side panels, back and roof of galvanized sheet production δ1.2mm the folded slot and strengthened, the use of screws to connect with the bottom box; 

 → overflow sink δ1.2mm galvanized sheet fold is made, the water curtain panels the δ1.0mm stainless steel plate, single-sided watering; 

 → Lighting with 40W dedicated fluorescent lamp, a set / Taiwan; 

 → the bottom of the cabinet to support 50 * 50 * δ2mm side through welding frame, and to install the M14 of Beta corolliflora * 100 adjustable foot cups; 

 → exhaust fan selected in Shanghai "decent" fuel injection cabinet dedicated centrifugal fan emissions, power 5.5KW---- 1 units; 

 → circulation transported water pump 1HP vertical Shanghai Baiquan "brand pumps and pumping cycle steel stencil; 

 → cabinet pumps and fans with separate control switch; 

 → pipes of 50mm diameter PVC pipes to make, equipped with high-pressure spray shower; 

 → exhaust pipe with 0.8mm galvanized plate production, and 10 m /; 



 The seventh, the dust removal device: 

 Manual dust cabinet: ----- (2) 

 → Dimension Specifications: W1000 * D1000 * H1700mm; 

 → use Dimensions: W1000 * D700 * H1100mm; 

 → outside the cabinet board board adopts 1.5mm cold folded steel plate bending with screw assembly; 

 → the end of the box using 2.0mm thick cold folded steel plate welded is made to connect the middle of the folder to seal; 

 → internal install two early effect of filter cotton, this cotton is preferable to take to clean up and replacement; 

 → top of the ventilation of the installation of a low noise 1HP centrifugal fan with regulator valve. 

 → PVC tube connected the exhaust to the spray shop Shuilian cabinet pumping exhaust wind pipe, formed within the state of the high airflow; 



 Paint line, screen printing lines